Alexander Walter Posted January 5, 2021 Posted January 5, 2021 Hi, I loose 20fps when connecting to vatsim via vpilot in the fslabs a320!? My specs: i7-9000, RTX2070Super, 32gb ram Does anyone have any ideas? This issue only occurs when on the ground. Quote
Sabine Meier Posted January 5, 2021 Posted January 5, 2021 Check in vpilot that it only uses flai for models. I suspect it loads fslabs models as well which you don’t want. Quote
Sven Sappa Posted January 5, 2021 Posted January 5, 2021 22 minutes ago, Koen Meier said: Check in vpilot that it only uses flai for models. I suspect it loads fslabs models as well which you don’t want. Actually had this happen on a event in EDDM and my FSLabs just went full stuka on final because frames were so low Hard lesson learned for me... Quote
Alexander Walter Posted January 5, 2021 Author Posted January 5, 2021 Thank you very much! Indeed you were right the fslabs models were ticked... It is fixed! Happy new Year Quote
Alexander Walter Posted January 5, 2021 Author Posted January 5, 2021 2 hours ago, Alexander Walter said: Thank you very much! Indeed you were right the fslabs models were ticked... It is fixed! Happy new Year Well it has made it A LOT better but it is still not what i think it could be... Quote
Sabine Meier Posted January 5, 2021 Posted January 5, 2021 I would consider tweaking some settings. Your system should easily reach 40fps. Quote
Rado Sutto Posted January 7, 2021 Posted January 7, 2021 Large airport full of AI traffic is fps killer. I use AIG traffic and fps drop is large. Quote
Michael Petersen Posted January 12, 2021 Posted January 12, 2021 Vpilot has always had huge CPU usage impact on my system even with few AI . I noticed its most bad when lots of online ATC is present. Sometimes restarting the app 2 or 3 times helps. (From 8-10%) cpu usage to about 1-2%. Michael Moe Quote
Alexander Walter Posted January 17, 2021 Author Posted January 17, 2021 So my FPS is at about 29-35fps at EGLL with traffic etc. and with that amount of fps it should be smooth, right? Well no it is jittery and laggy and inconsistant. my gpu usage is at 40% and cpu at 60%. In cruise i run at 65fps which is brilliant. My vram usage on the ground is also low at egll a little bit higher (5.0 out 7.1gb) and at others at about 3gb... I do not see where the issue could be does it mean a reinstal of p3d? btw. the issue also exists with other aircraft not only the fslabs! Thanks Quote
Norman Blackburn Posted January 17, 2021 Posted January 17, 2021 What are your specs and settings Alexander? Is this only online or offline too? Quote
stephen speak Posted January 17, 2021 Posted January 17, 2021 One update I did that was reasonable priced and not too hard to do..and made a big difference..I installed a solid state disk..easy to install and if you go Samsung like I did you can download a program that doesn’t so much copy your hard drive but sends all the contents of your hard drive to your new ssd and wipes your old drive..I immediately seen a difference steve Quote
Alexander Walter Posted January 18, 2021 Author Posted January 18, 2021 10 hours ago, stephen speak said: One update I did that was reasonable priced and not too hard to do..and made a big difference..I installed a solid state disk..easy to install and if you go Samsung like I did you can download a program that doesn’t so much copy your hard drive but sends all the contents of your hard drive to your new ssd and wipes your old drive..I immediately seen a difference steve I am on a 1tb ssd. Quote
Alexander Walter Posted January 18, 2021 Author Posted January 18, 2021 12 hours ago, Norman Blackburn said: What are your specs and settings Alexander? Is this only online or offline too? My specs are: i7-9700 32gb of ram, RTX2070 Super I use Active Sky and Active Sky cloud art and Envtex and Envshade. All on high performance setttings. The issue is a bit better when disconnected but it’s just not stable and or consistent. Quote
Norman Blackburn Posted January 18, 2021 Posted January 18, 2021 Ive a 2080ti and yes I can run it pretty much all to the right but your settings could be a little on the high side. Autogen back to normal, terrain sliders brought back a bit for a start. Save your settings before and after so you can easily compare. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.