Can not taxi.

[Jan Holmberg]

Hello!

I have problems with the aircraft not being able to taxi.
I have asked this question early in this forum, got good
help from several members, but unfortunately the problem occurs again.

Computer: CPU Intel Core i9 9900K 5.0GHz Turbo and Nvidia Geforce RTX Ti 11GB
Win 10 PRO 64, P3D v4 PRO, ORBX Global BASE Pack, GSX Level 2, Kaspersky Anti-Virus, Simbreif
and Figtsimlabs Airbus 320-X CFM (P3Dv4) in full screen mode both VC and 2D .

The airplane is configured and ready for taxi.
Parking brake is released and I will start to taxi.
Increases trottles to about 40%, nothing happens, when I increase to 90% the
airplane moves forward by 1 to 3 knots.
Following previous tips from members of the forum, everything works fine,
but suddenly the problem reappears

I got several tips from others flying the same aircraft, it worked well for
about a week, well the problem is back.

t is a fantastic skillfully created airplane, most of it is the simulator, when it works it is Christmas Eve.
Too bad if I give up and can't fly this nice bird.

Sincerely
Jan Holmberg

 

[Sabine Meier]

what is your hardware interface that you use. also this is in the general section where no support is provided.

[Jan Holmberg]

4 minutes ago, koen meier said:

what is your hardware interface that you use. also this is in the general section where no support is provided.

Thanks for your reply.

If it is joystick and pedals you mean, it is Ch Products.

Where should I write about my problem?
Getting different answers from different people?

[Sabine Meier]

if it takes 90% to start rolling then either your throttle isn't set up correctly or the aircraft fails to read the custom ground friction profile. 

there are multiple section on this forum. this was posted in the general section which doesn't provide support. there is an a3XX sub forum which does provide support except for its general sub part.

[David Warner]

Check your pedals sensitivity in P3d control options. Set the sensitivity to at least 100. They are probably at the default of 64 right now.

[Jan Holmberg]

4 minutes ago, David warner said:

Check your pedals sensitivity in P3d control options. Set the sensitivity to at least 100. They are probably at the default of 64 right now.

Thanks for your answer.
I'll be back when I test your tip.

[Jan Holmberg]

26 minutes ago, Jan Holmberg said:

Thanks for your answer.
I'll be back when I test your tip.

Hello again!

I have to tell you this.
Don't know if it has meaning.
The problem remained after I set the value to 100 for the brakes.

I'm using Active Sky P3Dv4.
If I do not start AS then everything works.
If I start AS before P3D, the problem seems to occur every time.

I've been a private pilot for almost my entire life.
Flew a Mooney M20 E, the best I did ;-)

Sincerely
Jan Holmberg

 

[Phil Tereny]

let's check if the brakes are constantly applied. Go to the overhead panel and turn off the green hydraulic pump as well as the hydraulic PTU. So you enable the alternate braking system, whose activity is shown on the brake pressure indicator. If this is not zero, then the brakes are applied and the vonfiguration of your brakes / hardware is wrong.

[Sabine Meier]

2 hours ago, Jan Holmberg said:

I'm using Active Sky P3Dv4.
If I do not start AS then everything works.
If I start AS before P3D, the problem seems to occur every time.

solution to try is to start active sky after you loaded in p3d. 

[Jan Holmberg]

24 minutes ago, Phil Tereny said:

let's check if the brakes are constantly applied. Go to the overhead panel and turn off the green hydraulic pump as well as the hydraulic PTU. So you enable the alternate braking system, whose activity is shown on the brake pressure indicator. If this is not zero, then the brakes are applied and the vonfiguration of your brakes / hardware is wrong.

Thanks for your tip!
I'll test according to your tip.

19 minutes ago, koen meier said:

solution to try is to start active sky after you loaded in p3d. 

 

19 minutes ago, koen meier said:

solution to try is to start active sky after you loaded in p3d. 

Thanks for your tip!
I'll test according to your tip.

[Stefan Busse]

Hi Jan,

i had the issue to, wenn i changed the livery of the bus. That means i chosen another bus.

Try to start the flight by the default F-22 on a parking position of your choise. Then load the bus (only one, don´t change!) and after this start AS4. 

[Jan Holmberg]

2 minutes ago, Stefan Busse said:

Hi Jan,

i had the issue to, wenn i changed the livery of the bus. That means i chosen another bus.

Try to start the flight by the default F-22 on a parking position of your choise. Then load the bus (only one, don´t change!) and after this start AS4. 

Thanks for your tip!
I will test according to your recommendation.